|
|
Post by Greg on Jan 27, 2013 1:32:44 GMT -8
I have the post for I-carver and Vcarve I will upload later when I locate it.
|
|
|
|
Post by Greg on Jan 29, 2013 7:05:18 GMT -8
This post is for photoVcarve Attachments:
|
|
|
|
Post by Greg on Jan 30, 2013 7:57:14 GMT -8
-Just used this post processor last night with Vectrics cut2d program and it works fine.
When I first started using a post with this machine I found that even if you have the machine set to use inch you still have to use mm in the gee code.
the machine will read the inch code thinking it is metric and cut a small square about 1/4".
Greg
|
|
|
|
Post by levi4032 on Feb 1, 2013 21:20:08 GMT -8
email vectrics and ask for pp in inches and they will send it to you without any problem
|
|
|
|
Post by Greg on Feb 1, 2013 23:26:36 GMT -8
That zip file has the inch code in it too, the I-carver will not work with inch code it reads it as metric and cuts a 1/4" cut and is done.
|
|
|
|
Post by levi4032 on Feb 11, 2013 4:09:08 GMT -8
They have both inch code and mm code and each work as they should just tell them you have an oliver machine and they will send it to you.
|
|
|
|
Post by Greg on Feb 11, 2013 8:13:25 GMT -8
These are their post files, I don't think you are reading what I am saying.
I use inch in all my settings and I have my machine set to "inch".
When I use the inch post the machine thinks the gee code is metric and cuts a small 1/4" square and quits.
It only reads in metric.
Greg
|
|
|
|
Post by klopek on Mar 5, 2013 9:01:15 GMT -8
I am using Vector Art 3d Machinest and they sent me a post processor code in inches and mm. I save the file i want to use with there post processor code and then when i try and use it with the intellicarve it says no file... so the cnc doesnt see the file.. Any ideas?
|
|
|
|
Post by gullyfoyle on Mar 5, 2013 10:08:41 GMT -8
|
|
|
|
Post by Greg on Mar 7, 2013 9:19:13 GMT -8
I am using Vector Art 3d Machinest and they sent me a post processor code in inches and mm. I save the file i want to use with there post processor code and then when i try and use it with the intellicarve it says no file... so the cnc doesnt see the file.. Any ideas? Try opening the G-code file with I-picture so it can check it then save it as a .gee code file. And make sure you use a metric post. Greg |
|
|
|
Post by Greg on Mar 15, 2013 23:32:05 GMT -8
Ok it appears gullyfoyle has found an error in the programming in the post processors.
It should be an easy fix but I want to test cut some scrap and see if it's right then I will delete the first zip file and re upload the new one.
Greg
|
|
|
|
Post by gullyfoyle on Apr 10, 2013 11:26:36 GMT -8
Did it work? Have you checked the latest version and made changes to them? Attachments:
|
|
|
|
Post by gullyfoyle on Apr 10, 2013 11:27:46 GMT -8
These were the latest two, inch in previous post, as of 3/13/13. I'm not sure if there is a newer version. Attachments:
|
|
|
|
Post by Greg on Apr 11, 2013 0:11:11 GMT -8
No the metric file works fine for me so I use it, those two have the same code as my first two.
The numbers 1.2 and 1.3 are wrong from the directions I read.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Apr 11, 2013 4:28:21 GMT -8
 Since my machine was built where they use the metric system, I am not gonna ask it to do in inches, hell of a lot easier for me to do the conversion, LOL
|
|
Since my machine was built where they use the metric system, I am not gonna ask it to do in inches, hell of a lot easier for me to do the conversion, LOL